Serving the Industrial requirement for over 50 years

Maghnelic

Maghnelic

Home >> Maghnelic

Maghnelic distributor in India

The Magnehelic gauge is the industry standard to measure fan and blower pressures, filter resistance, air velocity, furnace draft, pressure drop across orifice plates, liquid levels with bubbler systems and pressures in fluid amplifier or fluidic systems.

 

Magnehelic Differential Pressure Gauges

  • Model : 2000-Series
  • Range : 0….6… up to 1000 mmWC
  • Units : PA / mmWC / KPA Available
  • Dial Size : 100 MM
  • : 1/8″ NPT(F)


We offer Differential Pressure such as Digital Differential Pressure Gauge, Digital Differential Pressure Controller, Differential Pressure Transmitter, Differential Pressure Gauge, Scalable Differential Pressure Transmitter, Intrinsically Safe Differential Pressure Transmitter and many more items.  Allied corporation tools is leading Maghnelic distributor in India.

  • GI Magnehelic Gauge Box
  • Magnehelic Gauge SS Box
  • Industrial Magnehelic Gauges
  • Magnetic Gauge
  • Magnehelic Differential Pressure Gauge
  • Dwyer Differential Pressure Gauge
  • Magnehelic Gauge with S.S. Enclosure
  • Dwyer Make Magnehelic Differential Pressure Gauge
  • Digital Differential Pressure Gauges
  • Front Mount Differential Pressure Gauge
  • Dwyer Digital Differential Pressure Gauge
  • MS Flesh Type Magnehelic Gauge
  • Low Cost Sensocon Differential Pressure Gauge
  • Low Pressure Differential Gauge
  • Very Low Differential Pressure Gauge
  • Photohelic Switch / Gauges
  • Magnehelic Gauge Sensor
  • Differential Pressure Switch
  • Differential Pressure Transmitter
  • Mounting Box for Magnehelic Gauges

PRODUCT APPLICATIONS

  • Filter Monitoring
  • Air Velocity with Dwyer Pitot Tube
  • Blower Vacuum Monitoring
  • Fan Pressure Indication
  • Duct,Room or Building Pressures
  • Clean Room Positive Pressure Indication

 

SPECIFICATIONS

  • Service: Air And Non-Combustible, Compatible Gases (Natural Gas Option Available). Note: May Be Used With Hydrogen. Order a Buna-N Diaphragm. Pressures Must Be Less Than 35 PSI.
  • Wetted Materials: Consult Factory.
  • Housing: Die Cast Aluminum Case And Bezel, With Acrylic Cover, Exterior Finish is Coated Gray To Withstand 168 Hour Salt Spray Corrosion Test.
  • Accuracy:±2% (-HA model ±1) of FS (±3% (-HA ±1.5%) on -0, -100PA, -125PA, -10MM and ±4% (-HA ±2%) on -00, -60PA, -6MM Ranges), Throughout Range at 70°F (21.1°C).
  • Pressure Limits:-20 in Hg. to 15 PSIG.† (-0.677 bar to 1.034 bar); MP Option: 35 PSIG (2.41 Bar), HP Option: 80 PSIG (5.52 Bar).
  • Enclosure Rating:
  • Overpressure: Relief Plug Opens At Approximately 25 PSIG (1.72 Bar), Standard Gages Only. See Overpressure Protection Note On Catalog Page.
  • Temperature Limits:20 to 140°F (-6.67 to 60°C). -20°F (-28°C) With Low Temperature Option.
  • Size:4″ (101.6 MM) Diameter Dial Face.
  • Mounting Orientation: Diaphragm In Vertical Position. Consult Factory For Other Position Orientations.
  • Process Connections:1/8″ Female NPT Duplicate High And Low Pressure Taps – One Pair Side And One Pair Back.
  • Weight:1 lb 2 oz (510 g); MP & HP 2 lb 2 oz (963 g).
  • Standard Accessories: Two 1/8″ NPT Plugs For Duplicate Pressure Taps, Two 1/8″ Pipe Thread To Rubber Tubing Adapters And Three Flush Mounting Adapterswith Screws. (Mounting And Snap Ring Retainer Substituted For Three Adapters In MP & HP Gage Accessories.)
  • Agency Approval: Meets The Technical Requirements Of EU Directive 2011/65/EU (RoHS II).
  • Note:-SP Models Not RoHS Approved. Note: For Applications With High Cycle Rate Within Gage Total Pressure Rating, Next Higher Rating Is Recommended. See Options Page.